Wooden Toys Factory Introduces The Production Knowledge Of Wooden Products
2022-3-17
Wooden Toys Factory introduces how to make small wooden crafts:
1. Material selection and sketching: select the required wood, the size is appropriate, and leave room for mortise and tenon joints, and the surface should be flat and smooth. If the seam needs to be widened, it must be tightly bonded before it can be used. Put the drawn pattern on the wooden surface, and align the left and right up and down. If there are defects in the wood, such as knots and hollows, try to avoid the carved parts and stay in the carved parts. The pattern is usually placed on the finished wooden board and printed on the wood with multi-writing paper. You can also draw outlines to make rough blanks, and then engrave with the drawings.
2. Making rough blanks: After printing the drawings on the wooden boards, use tools such as saws, planers, shovels, etc. to make a rough outline first, which is a rough blank.
3. Saw outline: If it is an openwork pattern, it should be drilled with an auger first, and then cut through the wire saw after sawing the outline.
4. Chiseling: In the chiseling process, a round shovel is generally beaten with a mallet to chisel a fixed curve and outline, and dig out the largest part to be processed.
5. Shovel cutting: The fixed curve is chiseled, and the contour line can be shoveled. The flat shovel shovel requires the shoveled wood surface to leave traces and edges to keep it flat and smooth. Because the petals, moire and fringe cut by the shovel should be shoveled out layer by layer according to the size of the backhoe. For piercing and penetrating engraving, a back shovel or a round shovel should be used for shovel engraving. During the processing, it is necessary to prevent damage to the engraved pieces.
6. Carving: Use a carving knife to carve lines, use flat shovels and round shovels of different widths to carve finely, patterns on flowers and leaves, clothing patterns, animal body patterns, dragon whiskers on dragon heads, and special tools such as fat whiskers. to engrave.
Through the above introduction, Wooden Decorations Factory hopes that you can simply refer to the content of this article in future use.
https://www.wooden-crafts.net/
2022-3-17
Wooden Toys Factory introduces how to make small wooden crafts:
1. Material selection and sketching: select the required wood, the size is appropriate, and leave room for mortise and tenon joints, and the surface should be flat and smooth. If the seam needs to be widened, it must be tightly bonded before it can be used. Put the drawn pattern on the wooden surface, and align the left and right up and down. If there are defects in the wood, such as knots and hollows, try to avoid the carved parts and stay in the carved parts. The pattern is usually placed on the finished wooden board and printed on the wood with multi-writing paper. You can also draw outlines to make rough blanks, and then engrave with the drawings.
2. Making rough blanks: After printing the drawings on the wooden boards, use tools such as saws, planers, shovels, etc. to make a rough outline first, which is a rough blank.
3. Saw outline: If it is an openwork pattern, it should be drilled with an auger first, and then cut through the wire saw after sawing the outline.
4. Chiseling: In the chiseling process, a round shovel is generally beaten with a mallet to chisel a fixed curve and outline, and dig out the largest part to be processed.
5. Shovel cutting: The fixed curve is chiseled, and the contour line can be shoveled. The flat shovel shovel requires the shoveled wood surface to leave traces and edges to keep it flat and smooth. Because the petals, moire and fringe cut by the shovel should be shoveled out layer by layer according to the size of the backhoe. For piercing and penetrating engraving, a back shovel or a round shovel should be used for shovel engraving. During the processing, it is necessary to prevent damage to the engraved pieces.
6. Carving: Use a carving knife to carve lines, use flat shovels and round shovels of different widths to carve finely, patterns on flowers and leaves, clothing patterns, animal body patterns, dragon whiskers on dragon heads, and special tools such as fat whiskers. to engrave.
Through the above introduction, Wooden Decorations Factory hopes that you can simply refer to the content of this article in future use.
https://www.wooden-crafts.net/
Wooden Toys Factory Introduces The Production Knowledge Of Wooden Products
2022-3-17
Wooden Toys Factory introduces how to make small wooden crafts:
1. Material selection and sketching: select the required wood, the size is appropriate, and leave room for mortise and tenon joints, and the surface should be flat and smooth. If the seam needs to be widened, it must be tightly bonded before it can be used. Put the drawn pattern on the wooden surface, and align the left and right up and down. If there are defects in the wood, such as knots and hollows, try to avoid the carved parts and stay in the carved parts. The pattern is usually placed on the finished wooden board and printed on the wood with multi-writing paper. You can also draw outlines to make rough blanks, and then engrave with the drawings.
2. Making rough blanks: After printing the drawings on the wooden boards, use tools such as saws, planers, shovels, etc. to make a rough outline first, which is a rough blank.
3. Saw outline: If it is an openwork pattern, it should be drilled with an auger first, and then cut through the wire saw after sawing the outline.
4. Chiseling: In the chiseling process, a round shovel is generally beaten with a mallet to chisel a fixed curve and outline, and dig out the largest part to be processed.
5. Shovel cutting: The fixed curve is chiseled, and the contour line can be shoveled. The flat shovel shovel requires the shoveled wood surface to leave traces and edges to keep it flat and smooth. Because the petals, moire and fringe cut by the shovel should be shoveled out layer by layer according to the size of the backhoe. For piercing and penetrating engraving, a back shovel or a round shovel should be used for shovel engraving. During the processing, it is necessary to prevent damage to the engraved pieces.
6. Carving: Use a carving knife to carve lines, use flat shovels and round shovels of different widths to carve finely, patterns on flowers and leaves, clothing patterns, animal body patterns, dragon whiskers on dragon heads, and special tools such as fat whiskers. to engrave.
Through the above introduction, Wooden Decorations Factory hopes that you can simply refer to the content of this article in future use.
https://www.wooden-crafts.net/
0 Comentários
0 Compartilhamentos
344 Visualizações
English
Arabic
French
Spanish
Deutsch
Turkish
Dutch
Italiano
Russian
Romaian
Portuguese (Brazil)
Greek